GE · Oven / Range
GE Error Code F3
Oven temperature sensor open circuit. The control board has lost its temperature reference.
Caution — professional help advisedWhat the GE F3 code means
The F3 error code on a GE oven / range is a diagnostic fault reported by the appliance's main control board. In plain terms, it signals oven temperature sensor open circuit. The control board has lost its temperature reference. When this code appears, the oven / range pauses its current cycle as a safety measure to prevent water damage, electrical strain, or mechanical wear, and waits for the homeowner or a technician to inspect the underlying cause. Understanding exactly what the GE F3 code points to — and the most common parts and behaviors that trigger it — lets you decide whether this is a quick five-minute fix you can perform yourself, or a job that warrants a professional service call.
Tools and supplies you'll need
Gather the following items before you start so you don't have to stop mid-repair with the appliance partially disassembled. Having every tool within arm's reach also reduces the risk of forcing a stuck part, which is a common cause of secondary damage during DIY appliance repairs.
- Multimeter
- Phillips screwdriver
Comprehensive step-by-step troubleshooting & fixes
Follow each step in order. Before you begin, unplug the appliance from the wall outlet or flip the dedicated breaker so the unit is fully de-energized. Keep a towel and a shallow pan within reach in case any residual water escapes during the repair.
- 1
Disconnect power at the breaker and
Disconnect power at the breaker and let the oven cool.
- 2
Remove the rear panel and locate
Remove the rear panel and locate the temperature sensor (RTD) wire harness.
- 3
Test the sensor for about 1080
Test the sensor for about 1080 Ω at room temperature.
- 4
Replace the sensor if the reading
Replace the sensor if the reading is open or significantly out of range.
This repair can involve high-voltage wiring, sealed refrigerant or gas lines, or heavy moving parts inside the oven / range. Always disconnect the appliance from its power source at the breaker, shut off any associated water or gas supply, and let internal components cool before working on them. If you are not fully confident in any step, stop and contact a licensed appliance technician — the cost of a service call is far lower than the cost of an electrical shock, gas leak, or flooded floor.
Always disconnect power before servicing any appliance.
After the repair: how to verify the F3 code is gone
Once you've completed the repair, restore power to the GE oven / range and run a short test cycle — a quick rinse, drain, or self-diagnostic mode, depending on your model — to confirm the F3 fault has cleared. Watch the display for the first two to three minutes: if the code immediately reappears, the underlying component has not been fully resolved and you should recheck the part you serviced, inspect the wiring harness for a loose connector, or replace the related sensor. If the cycle completes normally and no fault is shown, your oven / range is safe to return to regular use. To prevent the F3 code from coming back, schedule a monthly check of debris filters, drain lines, door gaskets, and supply hoses — the vast majority of repeat-fault service calls trace back to gradual buildup that could have been cleared in five minutes.
Frequently asked questions about GE F3
Is it safe to keep using my oven / range while F3 is showing?
No. The control board has paused the cycle specifically to prevent further damage. Continuing to run the appliance can compound the issue and turn an inexpensive DIY fix into a major repair.
Will resetting the appliance clear the F3 code?
A power-cycle reset (unplugging for 5–10 minutes) may silence the code temporarily, but if the underlying fault is still present the code will reappear on the next cycle. Always perform the diagnostic repair above rather than relying on a reset alone.
How much does a professional charge to fix this?
In most U.S. metros, a licensed appliance technician charges between $120 and $300 for a diagnosis-plus-repair visit on this type of fault, with the higher end reflecting parts replacement. If the steps above resolve the issue, you'll typically save the full service-call fee.